Parts & Accessories

Years ago while Josh was working with the Team CSC at the Dauphine Libere, he noticed one of their mechanics using the most amazing little chuck to manage the disc wheel inflation. Unlike anything he had seen before, it was all metal and used a 'lollipop' lever on the side to lock onto the valve stems in disc wheels. The mechanic explained that these were made in Japan and were coveted by all the Euro-Pro mechanics due to their scarcity. So Josh set out to improve the design and make it available to cyclists everywhere. - Full metal construction, guaranteed for 25 years and covered by SILCAShield - Can effectively seal on valve stems as short as 10mm! - Uses SILCA 254 High-Tech Elastomer gasket - Adjustable gasket pre-load allows for a custom fit on any valve as well as compensation for gasket wear - Male Schrader thread fits into any Schrader chuck, or use SILCA Thread-On Schrader Adapter to fit a bare hose - Bullet-proof high-pressure, disc-compatible chuck for high-pressure situations.

A Schrader valve adapter allows using the JoeBlow Ace floor pump for quickly pumping forks and rear shocks. Built-in air release knob allows fine tuning air pressure.

Have an old pump lying around that doesn't work with the standard Presta valves? This is your solution! Built to convert your old schrader pump into a Presta pump!

Replacement gasket for the SILCA HIRO Chuck

A lightweight aluminum adapter allows the use of a Schrader pump on Presta tubes.

- Solution for mounting pumps and C02 inflators on frames or seatpost - Soft rubber block and Velcro loops hold pumps tightly

Prestacycle redesigned the Head and Washer fit onto bike wheels easier with more room. Prestacycle's new Quick-Click2 design engages the Presta valve just below the cap threads. The head is very easy to get on and off, and gives a nice “click” feeling when it’s installed in the right position. Safe for all types of Presta valves, including tubeless and tubeless-conversion valves. Will not harm newer lightweight performance valves. Fits Quick-Click2 Prestaflator Push/pull Presta heads. Does NOT fit other brands of Disc Wheel heads.

Quick-Clip design for frequent Schrader use. Prestacycle's oversized spring stands-up to high bicycle pressure for a good seal and safety. The compact angle head goes where even floor pump heads can’t reach, like kids bikes and small scooter tires! Made with 6061-T6 Alloy – it’s as strong as Brass and only 1/3 the weight. Patent-pending 2-way connector screws onto the Prestaflator threaded connector or directly clamps to a hose.

- Replacement brake hose for MT series brakes - Hose length: 2500mm - Black

This is a replacement hose for your Lezyne Micro Floor Digital Drive pump. It offers an integrated, highly advanced, inline digital gauge and ABS Flip-Thread chuck.

• Presta and Schrader valve compatible head • Hose and head kit fits most floor pumps

- Genuine Sunlite replacement hose - Type: Fits Sunlite #4301 : 16 5.8mm

- Genuine Sunlite replacement hose - Type: Fits Sunlite Frame Pump : 5.25mm

If you have a SILCA PISTA made since 1946, a SUPERPISTA since 1989, or any of the Impero Frame Pumps since 2015, it has a check valve assembly like this to ensure that air can only go in one direction

- Comes with Dual Head - Compatible with all Planet Bike floor pumps - #1002-5 Auto head with hose can be used as a substitute for this item and is compatible with all pumps that used the dual head

Bag of 3 replacement washers for EVA heads on all SKS floor pumps

- Replacement ABS Flex Hose for Lezyne hand pumps - Presta/Schrader ABS Flex Hose for HP, HV, Alloy, Pressure, and Tech Drive hand pumps

Why have your CO2 cartridges rattling around in a seat bag when you can get Xlab's X-Nut Inflation Holder and store them behind your saddle? It holds two threaded CO2 cartridges and an inflator (each sold separately) in an easy-access location. The X-Nut is compatible with Xlab's Carbon and Super Wings.

Mounting kit for Mini Morph and Road Morph G.

The Iconic SILCA 24.1 gasket is the heart of the press-on Presta chuck. The current 242 gasket utilizes a high tech and very red, fully synthetic elastomer base material.

Park Tool's Pump Rebuild Kit contains one #1081 head as well as one #1087 plunger gasket for their PFP-3, PFP-6 and PFP-8 floor pumps.

Easily adapts schrader only air compressors, floor pumps, and mini pumps to work with presta valves

Problem Solvers 90 degree Presta valve inflator is used to inflate disc wheels, thanks to its narrow, low-profile head. • Presta valve • 90 degree inflator works with most pump heads